The writer is making several good pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this content down the page.
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately tough job. If the old tub is easily easily accessible, the task can relocate immediately; if you have to open a wall to eliminate the old bathtub and position the new bathtub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub and also set in the new one. Ensure you have qualified yourself for the task and also fit trying it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to think about using one before you begin. Chances are you may need a professional plumber to make tube links.
This post will certainly help you install a new tub in your bathroom if you have already gotten a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material checklist ought to make up the following:
Getting ready for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain any water remaining in the system. The process of removing the existing faucets can be quite troublesome due to the restricted accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Using the two wood boards under its feet, position the bath tub in the needed setting. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bath tub until the level reads level.
To install taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the water as well as check all joints as well as new pipework for leaks as well as tighten them if needed. Fill the bathtub and also check the overflow outlet as well as the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait until the bathtub has been used at least once as this will settle it into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, causing the water to permeate the wall between the bath and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Leave a review down the page. We would be glad to know your insights about this blog posting. Hoping that you visit us again later on. Sharing is caring. Helping others is fun. Thanks for taking the time to read it.
Explore